Motorola HT 1000 User Manual Download | Manualshive

Page: 114 / 205

background image

108

Repeater Access
Configuration

From the MAIN MENU, press

F4, F3, F7, F3

and then

F2

to access this

screen.

This screen CANNOT be accessed for JT1000 model radios. For other
models, this screen can be accessed only when the Signalling Type field on
the MDC CONFIGURATION (

F4/F3/F7/F3

) screen is set to MDC1200. It

may also be accessed by selecting MDC1200 in the Signalling Type
field and pressing

F2

in the STAR CONFIGURATION screen (

F4/F3/F7/

F3

).

Function Key Descriptions

F5

- PRINT

Prints the current system configuration.

Field Definitions

Accept Alert

Use the UP/DOWN arrow keys to enable/disable this option. If this
feature is enabled, the RAT accept tone will be generated when the RAT
button is pressed.

The default is Enabled.

Silent Pretime (ms)

Enter the desired value directly or use the UP/DOWN arrow keys to
make your selection. The setting in this field determines the duration
of Repeater Access Pretime which can range from 0 to 2550 ms in 10-
ms increments.

The default is 510 ms.

RAT Codes (1 - 8)

Enter the desired value directly or use the UP/DOWN arrow keys to
make your selection. Each code (consisting of four-character
hexadecimal values, 0000-FFFF) represents the 16-bit ID of the
Repeater to be selected.

The defaults are FFF0 through FFF7.

DCGCB

MOTOROLA Radio Service Software Use

<:

keys to enable/disable feature

HT/JT1000/VISAR Model : Use <Enter> to go to next feature.
Serial:
CHANGE:RADIO:SIG:MDC:RAT ID

Repeater Access Configuration
-----------------------------

Accept Alert...............Enabled Code 1...............FFF0
Code 2...............FFF1
Silent Pretime (ms).............510 Code 3...............FFF2
Code 4...............FFF3
Code 5...............FFF4
Code 6...............FFF5
Code 7...............FFF6
Code 8...............FFF7

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP PRINT EXIT

«
...
112
113
114
115
116
...
»

Summary of Contents for HT 1000














































































































































































































Reviews:

No comments

Related manuals for HT 1000

Brand: Hama Pages: 24

Brand: Hama Pages: 4

Brand: Panasonic Pages: 7

Brand: Marathon Electric Pages: 73

Brand: Buck Rogers Pages: 58

Brand: Oxygen Pages: 15

Brand: AudioSonic Pages: 45

Brand: Uniden Pages: 12

Brand: EDIFIER Pages: 6

Brand: R&S Pages: 81

Music Angel 12031

Brand: QooPro Pages: 24

Brand: JRC Pages: 4

SureCross DX80SRxM-H

Brand: Banner Pages: 4

Brand: Denver Pages: 6

Brand: Powermate Pages: 12

Brand: auna Pages: 152

Brand: Ulvac Pages: 50

Brand: Briggs & Stratton Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands