Motorola HT 1000 User Manual Download

Page: 9 / 205

Equipment
Checklist

Listed below are all the equipment required to program a HT 1000,
JT1000, or VISAR radio using the RSS.

IBM Personal Computer

It is

strongly recommended

that this RSS be run on an IBM PC, IBM

PC compatible or PS/2 computer with the following minimum
configuration:

• 80286 CPU or higher;

• An asynchronous communications adapter;

• MS-DOS 5.0 or higher (with DOS running in high memory);

• 4 Megabytes of RAM or greater; and

• At least 512K of free, conventional memory. (The DOS CHKDSK

command can be used to determine the amount of free RAM
available on your computer.)

Radio Interface Box (RIB)

Part Number

RLN-4008B

(includes internal 9-volt Battery). Allows the

computer to communicate with the radio via its asynchronous
communications adapter.

Wall-Mounted Power Supply
(for RIB)

Part Number

01-80357A57

– 120V AC/DC Converter

Part Number

01-80358A56

– 220V AC/DC Converter

Part Number

60-82728J01

– 9V Battery

Computer Interface Cable

Part Number

30-80369B71

– 25-pin D connector (computer end),

15-pin D connector (RIB end)
Part Number

30-80369B72

– 9-pin D connector (computer end),

15-pin D connector (RIB end)

This hardware connects the computer’s asynchronous
communications adapter to the RIB.

Program/Test Cable

Part Number

RKN4035D

for HT/JT1000 radios and Part Number

RKN4042A

for VISAR radios. Provides electrical connections to the

RIB, Portable Products Test Set, and the radio.

HT/JT1000/VISAR RSS

Part Number

RVN-4098G

(One 3-1/2 inch double-density floppy disk

is included.)

Portable Products Test Set

Part Number

RTX-4005B

. Provides the capability to test many

transmitter and receiver functions. Transmitter modulation and
keying can be tested without disassembling the radio. The Test Set is
used in conjunction with the programming/test cable.

Battery Eliminator

Part Number

RLN1014A

for HT/JT1000 and

RLN4327A

for VISAR

radios. Replaces the battery pack during servicing.

5 Amp Power Supply (for radio)

Supplies power to the battery eliminator.

Cloning Cable

Part Number

RLN4036A

for HT/JT1000 radios and Part Number

RKN4043A

for VISAR radios. Used to connect two radios so that the

codeplug (personality) of the source radio can be programmed into the
target radio.

Summary of Contents for HT 1000














































































































































































































Search results

Summary of Contents for HT 1000

Reviews:

Related manuals for HT 1000

Brands by name

Popular brands

Motorola HT 1000, User Manual

Search results

Summary of Contents for HT 1000

Reviews:

Related manuals for HT 1000

Brands by name

Popular brands