Motorola HT 1000 User Manual Download

Page: 105 / 205

Signalling Options

From the MAIN MENU, press

F4, F3

and then

to access this screen.

This menu provides access to signalling option configuration screens:
Quik-Call II, MDC/STAR/ATIS, Single Tone, and DTMF.

Note:

The MDC/STAR/ATIS option (

) will not be visible if a

JT1000 codeplug is loaded into the work space.

Function Key Descriptions

- QUIK-CALL II

(Quik-Call II Options)

Brings up a screen from which you can configure Quik-Call II options.

- MDC/GS/AT OPT

(MDC/STAR/ATIS Options)

This function will NOT be visible for JT1000 model radios. Brings up a
screen from which you can configure MDC/STAR/ATIS options.

- SINGLETONE

(Singletone Configuration)

This function will be visible only for VISAR, HT 1000 “B”, and JT1000
models. Brings up a screen from which you can configure Single Tone
options.

- DTMF LIST

(DTMF Phone List)

This function will be visible only for models with DTMF keypad. Brings up
a screen from which you can configure DTMF options.

DCG

MOTOROLA Radio Service Software Select a function key, F1-F10.
HT/JT1000/VISAR Model :
Serial:
CHANGE:RADIO:SIG OPT

Signalling Options Menu
-----------------------

F1 - HELP
F2 - Quik-Call II Options
F3 - MDC/STAR/ATIS Options
F4 - Singletone Configuration
F5 - DTMF Phone List
F6 -
F7 -
F8 -
F9 -
F10 - EXIT

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP QUIK MDC/GS/ SINGLE- DTMF EXIT
CALL II AT Opt TONE LIST

Summary of Contents for HT 1000














































































































































































































Search results

Summary of Contents for HT 1000

Reviews:

Related manuals for HT 1000

Brands by name

Popular brands

Motorola HT 1000, User Manual

Search results

Summary of Contents for HT 1000

Reviews:

Related manuals for HT 1000

Brands by name

Popular brands