Motorola HT 1000 User Manual Download | Manualshive

Page: 86 / 205

background image

80

JT1000
Configuration
Options

At the MAIN MENU, press

F4, F3, F2

and then

F3

to access this screen.

This menu allows you to modify the system configuration for JT1000
radios only. This screen will NOT be accessible for HT 1000 or VISAR radio
models.

Function Key Descriptions

F5

- PRINT

Prints the current system configuration.

F9

- DEFAULT

Resets the fields on this screen to their default values.

Field Definitions

User Programming

Use the UP/DOWN arrow keys to enable or disable User Programming
mode. If this feature is enabled, the radio user will be able to program
frequency, squelch coding, power, and bandwidth, and will also be
able to use the Multi-Select PL/DPL feature.

Note that user programming can also be enabled/disabled on a
channel-by-channel basis by configuring this field on the CHANNEL
CONFIGURATION screen (

F4/F4

).

Note:

When User Programming Mode is enabled, Normal Dispatch

Operation will be disabled, and the radio will not unmute to channel
traffic. The menu timeout feature will prevent the radio from
remaining in this state for an extended period.

The default is Enabled.

Programming Password

This feature allows you to restrict access to programming for
frequency, squelch coding, power, and channel bandwidth. The
password is limited to 8 numeric characters or less. The minimum
password length is one character. To set a password of less than 8
characters, be sure to use the

Del

key to remove any excess digits.

Spaces are not allowed as part of the password.

The default is 581000.

DCBC

MOTOROLA Radio Service Software Use

<:

keys to scroll values.

HT/JT1000/VISAR Model : H01SDH9PA3AN Use <Enter> to go to next feature.
Serial:
...RADIO:SYS CONFIG:JT1000 OPTIONS

JT1000 CONFIGURATION OPTIONS
----------------------------

User Programming..............Enabled Alert Tones....................Enabled
Programming Password...........581000 Freq. Range Low Limit............450.0
Menu Timeout Period (sec)..........15 Freq. Range High Limit...........512.0

Auto-backlight................Enabled Display Format.........Channel Number
Backlight timer (sec)...............5 TX Power w/Alkaline Batt...Always Low

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
HELP PRINT DEFAULT EXIT

«
...
84
85
86
87
88
...
»

Summary of Contents for HT 1000














































































































































































































Reviews:

No comments

Related manuals for HT 1000

Brand: Makita Pages: 12

LUNCHBOX LB-100

Brand: Sangean Pages: 1

Brand: Eton Pages: 18

Brand: Sirius Satellite Radio Pages: 2

Brand: FMUser Pages: 8

Brand: Curtis Pages: 16

Brand: Champion Pages: 29

Brand: Logic Pages: 36

Brand: Campbell Pages: 130

Brand: Naxa Pages: 9

Brand: Sonos Pages: 18

Brand: SOUNDMASTER Pages: 4

Brand: MartinLogan Pages: 8

Brand: Curtis Pages: 1

Brand: Curtis Pages: 11

Brand: Sepura Pages: 12

GALE FORCE PT8500E

Brand: PENTAGON Pages: 25

Brand: Sharp Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands