manualshive.com logo in svg

Microplex M204, Installation And Configuration Manual

Share
Download
Microplex M204 Installation And Configuration Manual Download Page 18

10

GETTING TO KNOW THE M204: Overview of Print Server Installation

Overview of Print Server Installation

This section will provide an overview of the basic steps required to install the M204 in
the various supported environments: Unix, Novell (PSERVER and RPRINTER), Net-
BIOS over TCP/IP, and AppleTalk.

Before installing the Print Server, it may be useful to look at Appendix A, Planning
Your Print Setup on page 183 for advantages/disadvantages of various configuration
options.

Basic Unix Configuration

The following outlines the basic steps required to add a M204 to a Unix network.

Once the unit is physically attached to the network, you need to:

1

Assign an IP address, netmask, and possibly a default router to the M204. This
can be done in several ways:

•

automatically with ezsetup or npconfig (option 1 from the Main Menu).
Please see page 24.

•

manually through the network using ARP. Please see page 25.

•

manually through the network using RARP. Please see page 26.

•

manually through the network using BOOTP. Please see page 27.

•

manually through the COM port. Please see page 28.

2

Configure the print setup on the host to print to this unit. This can be done in sev-
eral ways depending on your host system.

•

automatically with ezsetup or npconfig (Option 2 from the Main Menu)
Please see page 24.

•

manually for a BSD Unix environment. Please see page 35.

•

manually for a System V Unix environment. Please see page 39.

•

manually for a AIX Unix environment. Please see page 47.

Note

Summary of Contents for M204













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands