La Marzocco Linea PB Manual Download Page 38

Page: 38 / 112

Display

Operating Procedure

Description

Programming Mode

When the espresso machine is turned on, press and hold the T3 button

to access the “Barista” programming.

After about 5 seconds the following screen is displayed.

Press the T3 button

to enter the doses programming procedure.

Press the button T1

or T2

to display the following menu.

Press the T3 button

to access the menu, then navigate using T1

and T2

to choose between

PULSES

MASS

and

BREWRATIO

• This parameter allows the operator to

select the coffee brewing mode among
those available: pulse, mass and brew
ratio.

• PULSE mode: control of doses in volume
• MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the

coffee powder and the weight of the
drink

Group Dose

Settings

Group Dose

Settings

LaMarzocco 00:00

CB 93.8

C SB

G1 Dose

Settings

Program Dose

Scales

Group 1 Mode

PULSES

“Barista” Programming

(only on ABR espresso machine models)

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands