La Marzocco Linea PB Manual Download Page 56

Page: 56 / 112

Display

Operating Procedure

Description

Programming Mode

“Barista” Programming

Cup Warmer

Cup Warmer

DISABLED

When the espresso machine is turned on, press and hold the T3 button

. After about 5 seconds the

following screen is displayed.

Move between the parameters using the buttons T1

and T2

until the display shows:

Press the T3 button

to enter the menu, move between the parameters using the buttons T1

and

to select

ENABLED

DISABLED

, press the T3 button

to confirm the option.

LaMarzocco 00:00

CB 93.8

C SB

Program

Dose

Cup Warmer

DISABLED

• This parameter allows the operator to

enable or disable the cups heating
function.

• This function is displayed only on the

models of espresso machine equipped
with this accessory.

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands