La Marzocco Linea PB Manual Download Page 80

Page: 80 / 112

Display

Operating Procedure

Description

Programming Mode

Tea Dose
Settings

After accessing the “Technical” programming menu and entering the password, use the buttons T1

and

until the following screen is displayed.

Press the T3 button

to enter the menu.

Press the T3 button

to enter the menu, move between the parameters using the buttons T1

and

to select

ENABLED

DISABLED

, press the T3 button

to confirm the option.

To program the brewing time, press the tea button to start and then press it again to stop when the desired dose
is achieved.
Now the saved brewing time is displayed.

Enter Password

******

• This parameter allows the operator to

program the amount of water (brewing
amount) for the tea button.

• This feature can be enabled or disabled.

Tea Dose

ENABLED

Tea Dose
Settings

Tea Dose

Program

Tea Dose

Press Tea Button

To Stop

Press Tea Button

To Program

Tea Dose Saved

5.0 Seconds

“Technical” Programming

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

La Marzocco Linea PB, Manual, Page: 80 / 112

Search results

Summary of Contents for Linea PB

Reviews: