La Marzocco Linea PB Manual Download Page 27 | Manualshive

Page: 27 / 112

background image

EN

27

Display

Operating Procedure

Description

Programming Mode

Start Up Procedures

The following is the procedure for turning
on the power to the espresso machine.
• Please follow the procedures carefully

to avoid any damage to the espresso

machine.

• Proceed checking for water connection

to the espresso machine.

• Proceed making sure you have filled the

boilers.

• For the MP version, ongoing warming is

indicated by the timer located on the
groups using digit rotation.

Turn the Main Switch to the 1 position.

The message shown to the left will be displayed when the espresso machine is switched on.

To complete the start up process, press any button. The screen shown to the left will be displayed. The
rectangles next to CB and SB indicate the warming up of the water contained in the boilers. When the set
temperature is reached, these rectangles turn off and all the lights of the buttons turn on. Now the machine
is ready for use. During the normal operation of the machine, the flashing of the rectangles indicates the
intermittent heating necessary for maintaining the temperature.

NOTE:

Ensure all air is removed from the group prior to staring the espresso machine.

This only needs to be completed once during the initial setup or when water is drained from the coffee boiler.

Instructions for bleeding the groups of air can be found in the Installation Guide.

Turning the Espresso

Machine On

HAZARDOUS VOLTAGE DISCONNECT FROM POWER

SUPPLY BEFORE SERVICING

WARNING

OFF

00:00

LaMarzocco 00:00

CB

O

93.8

°

C SB

O

OFF

00:00

1

3

2

«
...
25
26
27
28
29
...
»

Summary of Contents for Linea PB

















































































































Reviews:

No comments

Related manuals for Linea PB

Brand: Fellow Pages: 29

Home Bakery Virtuoso BB-PAC20

Brand: Zojirushi Pages: 52

Brand: knIndustrie Pages: 2

Brand: Hamilton Beach Commercial Pages: 36

Brand: Jenn-Air Pages: 10

SCLUSIVO DCF210TTC

Brand: DeLonghi Pages: 1

Brand: OK. Pages: 63

Brand: U-Line Pages: 44

Brand: DONPER Pages: 38

Brand: Magio Pages: 23

Brand: Vitek Pages: 25

Brand: Royal Pages: 34

Brand: Hamilton Beach Pages: 10

Brand: KitchenAid Pages: 8

Brand: KitchenAid Pages: 44

Brand: KitchenAid Pages: 48

Brand: CAB Pages: 28

Brand: La Cimbali Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands