La Marzocco Linea PB Manual Download Page 90

Page: 90 / 112

Display

Operating Procedure

Description

Programming Mode

“Technical” Programming

(only on espresso machine models WITHOUT sight glass)

To exit the menu move between the parameters using the buttons T1

and T2

until the exit menu

is displayed. Press the T3 button

to exit the menu.

Turn the Main Switch to the 0 position.

Now it is possible to turn on again the espresso machine; set the main switch to position 1 and press any button
to complete machine switch on.

Steam Boiler

Exit

LaMarzocco 00:00

CB 93.8

C SB

Steam Boiler

Settings

• The parameter “Level Sensit.” allows the

technician to select the probe sensitivity
for steam boiler filling according to water

hardness.

• The black connection cable corresponds

to the working level probe.

• The red connection cable corresponds to

the minimum level probe.

• The sensitivity default value is high.

Restart Machine

for Changes

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands