La Marzocco Linea PB Manual Download Page 39

Page: 39 / 112

Display

Operating Procedure

Description

Programming Mode

(only on ABR espresso machine models)

“Barista” Programming

Press T1

or T2

until the display shows the exit menu, press the T3 button

to return to the

“Barista” programming.

Press T1

or T2

to continue with the programming of the other parameters.

Press T2

and T3

at the same time to exit the programming mode and return to the normal use of the

espresso machine.

• This parameter allows the operator to

select the coffee brewing mode among
those available: pulse, mass and brew
ratio.

• PULSE mode: control of doses in volume
• MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the

coffee powder and the weight of the
drink

Group Dose

Settings

Exit

Group 1

LaMarzocco 00:00

CB 93.8

C SB

Program Dose

Scales

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands