La Marzocco Linea PB Manual Download Page 37

Page: 37 / 112

Display

Operating Procedure

Description

Programming Mode

(only on ABR espresso machine models)

“Barista” Programming

Press Enter

To Exit

Press the T3 button

to return to the doses programming.

Press T1

or T2

until the display shows the exit menu, press the T3 button

to return to the

“Barista” programming.

Press T1

or T2

to continue with the programming of the other parameters.

Press T2

and T3

at the same time to exit the programming mode and return to the normal use of the

espresso machine.

• This parameter allows the operator to

program the amount of coffee (brewing
weight) for each button on the keyboard.

• Once programmed, the button remains

lighted.

• It is possible to set the dose for both a

short and a long shot on the same key.

• It is possible to copy the doses of any

key to the others.

Group Dose

Settings

Group Dose

Exit

LaMarzocco 00:00

CB 93.8

C SB

Program Dose

Scales

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands