La Marzocco Linea PB Manual Download Page 51

Page: 51 / 112

Display

Operating Procedure

Description

Programming Mode

“Barista” Programming

Tea Dose

Tea Dose
Settings

When the espresso machine is turned on, press and hold the T3 button T3

to access the “Barista”

programming. After about 5 seconds the following screen is displayed.

Move between the parameters using the buttons T1

or T2

until the display shows:

Press the T3 button

to enter the menu.

Press the T3 button

to enter the menu, move between the parameters using the buttons T1

and T2

to select

ENABLED

DISABLED

, press the T3 button T3

to confirm the option.

To program the brewing time, press the tea button to start and then press it again to stop when the desired
dose is achieved.
Now the saved brewing time is displayed.

LaMarzocco 00:00

CB 93.8

C SB

Program

Dose

Tea Dose
Settings

• This parameter allows the operator to

program the amount of water (brewing
amount) for the tea button.

• This feature can be enabled or disabled.

Tea Dose

ENABLED

Program

Tea Dose

Press Tea Button

To Stop

Press Tea Button

To Program

Tea Dose Saved

5.0 Seconds

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands