La Marzocco Linea PB Manual Download Page 84

Page: 84 / 112

Display

Operating Procedure

Description

Programming Mode

“Technical” Programming

After accessing the “Technical” programming menu and entering the password, use the buttons

and

until the following screen is displayed.

Press the T3 button

to enter the menu.

Press the T3 button

to enter the menu, move between the parameters using the buttons

and T2

to select

ENABLED

DISABLED

, press the T3 button

to confirm the option.

Press the T3 button

to enter the menu, move with the buttons

and T2

to set the

desired temperature, press the T3 button

to confirm the value.

The first value indicates the time in seconds between the detection of the need to fill and the start of filling.

The second value indicates the time in seconds between filling and its actual end.
Press the T3 button

to enter the menu, move with the buttons

and T2

to set the

desired automatic filling time, press the T3 button

to confirm the value.

• This parameter enables the technician

to set various parameters of the steam

boiler.

• The temperature of saturated water is

proportional to the pressure inside the

Steam Boiler. Therefore it is possible to

regulate the pressure of the steam boiler

by means of electronic temperature

control. Please use the following tables

as reference when setting the steam

boiler temperature.

Steam Boiler

Settings

Steam Boiler

Settings

Steam Boiler

Steam Boiler

ENABLED

Enter Password

******

Steam Temp.

123,7

C 123,5

Autofill Delay

2 start 2 stop

THE STEAM BOILER CONTAINS WATER AT ELEVATED TEMPERATURES.

WATER TEMPERATURE OVER 52°C CAN CAUSE SEVERE BURNS INSTANTLY OR DEATH FROM SCALDING.

DANGER

Temperature

Pressure

247°F/119°C

1.0 bar

260°F/127°C

1.5 bar

272°F/133°C

2.0 bar

The saturation temperature of water will vary

with ambient atmospheric pressure.

Tables in this manual are created for atmospheric

pressure at sea level. Slight adjustment in temperature

will be required for elevations other than sea level.

CAUTION

2
3

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands