background image

EN

6

1) General description

The machine is built in 2, 3, and 4 coffee 
group versions and is essentially composed 
of the following parts:

•   Steam  Boiler  (produces  steam  and  hot 

water);

•   Coffee (“saturated”) boiler;
•   Brewing groups;
•   Exterior Cover;
•   Water pump.

2) Description of the various parts

• Steam Boiler
The Steam Boiler consists of a cylindrical 
tank,  of  varying  length  according  to  the 
number of coffee groups, which is made of 
AISI 300 series stainless steel. Each unit is 
subjected to a hydraulic test, at a pressure of 
6 bar, and has an operating pressure of 1.3-
1.5 bar. The following is a list of effective 
volumes and power ratings according to the 
number of groups installed:

2 groups      

7 liters 

3 groups      

11 liters  

4 groups      

15 liters 

Covers  are  welded  at  either  end  of  the 
cylindrical tank and on one of them there 
is a housing for the water heating element, 
which  allows  the  steam  boiler  to  reach 
operating pressure within approximately 25 
minutes. Operating pressure is maintained

by an electronic temperature probe with
a  PID  controller.  The  steam  boiler  has 
various fittings used for safety devices, for 
supplying hot water and steam, and for the 

heating element.

• Coffee boiler

The Coffee Boiler consists of a cylindrical 
tank,  of  varying  length  according  to  the 
number  of  coffee  groups,  which  is  made 
of  AISI  300  series  stainless  steel.    Each 
unit  is  subjected  to  a  hydraulic  test,  at  a 
pressure  of  18  bar,  and  has  an  operating 
pressure  of  9  bar.    The  following,  table 
is  a  list  of  effective  volumes  and  power 
ratings according to the number of groups 
installed:

2 groups      

3.4 liters

3 groups      

5 liters

4 groups      

6.8 liters

Covers  are  welded  at  either  end  of  the 
cylindrical tank and on one of them there 
is a housing for the water heating elements.  
The  temperature  of  the  coffee  boiler  is 
maintained  by  an  electronic  temperature 
controller  (PID  capable)  with  an  accuracy 
of 0.2°C.  The brewing groups are installed 
on the boiler.

• Brewing groups

They  consist  of  a  precision  casting  made 
of  stainless  steel.  The  brewing  group 

accepts  the  portafilter  used  to  hold  the 
ground  coffee;  the  espresso  flows  through 
the  brewing  group,  through  the  portafilter 
basket,  through  the  portafilter  spout,  and 
into the cup(s) after the brewing button has 
been pressed.

• Exterior cover

The  exterior  consists  of  painted  and 
stainless  sheet  steel  panels.  To  provide 
good aesthetics, to optimize ergonometrics 
for the operator and to reduce the chance 
of damage to a minimum.

• Water pump

The rotary vane pump, is installed on the 
water supply tubing and is set up to operate 
anytime  the  coffee  groups  are  activated, 
and  through  an  autofill  system  whenever 
the water boiler needs to be replenished.

• Sound pressure

The  weighted  sound  pressure  level  of  the 
machine is lower than 70dBA.

• Water inspection window

The position of this device enables to verify 
only water presence inside the steam boiler. 
The  water  level  in  the  window  provides  a 
reference about the water level in the steam 
boiler, but doesn’t represent it in a directly 
proportional  way,  1/3  of  the  windows  is 
equal to approximately 1/2 of the boiler.

Summary of Contents for Linea PB

















































































































Reviews: