La Marzocco Linea PB Manual Download Page 62

Page: 62 / 112

Display

Operating Procedure

Description

Programming Mode

Press T1

or T2

until the display shows the exit menu, press the T3 button

to return to the

“Technical” programming.

Press T1

or T2

to continue with the programming of the other parameters.

Press T2

and T3

at the same time to exit the programming mode and return to the normal use of the

espresso machine.

• This parameter allows the operator to

program the amount of coffee (brewing
amount) for each button on the
keyboard.

• The brewing amount can be set in terms

of time (sec. ) or pulses. This number
refers to the number of pulses that the
flowmeter sends to the CPU.

• Once programmed, the button remains

lighted.

Group Dose

Settings

Group Dose

Exit

Program Dose

LaMarzocco 00:00

CB 93.8

C SB

“Technical” Programming

(available up to the 1.6.3 software version)

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands