La Marzocco Linea PB Manual Download Page 109 | Manualshive

Page: 109 / 112

background image

EN

109

“Technical” Programming

Troubleshooting

• This espresso machine is equipped with several feedback mechanisms that alert the operator when an unusual condition occurs.

Additionally the espresso machine will warn the operator when certain parameters fall below or above the programmed point. These
errors and warnings will appear as a message in the display.

• The following section will describe errors and warnings that may appear in the display.

Description

Message Solution

Message

This message is displayed when the CPU does not

detect a full signal from the steam boiler within the

set time interval.

When this message is displayed the CPU also shuts down and turns off power to the machine (see

the parameter “Level Timeout”). Press the ON/OFF button to reset this error.

Steam Boiler

Autofill Failed

Coffee Boiler 1

Probe Failed

This message is displayed when the CPU does not

detect the temperature probe.

When this message is displayed the CPU shuts down and turns off the machine.

The way to reset this error is to verify and to reconnect the temperature probe.

SB Filled?

This message is displayed during first installation

and when preset of settings is made.

Push enter if Steam Boiler is filled. Verify the presence of water looking the sight glass.

Groups Bled?

This message is displayed during first installation

and when preset of settings is made.

Push enter if groups have been blend ie no air is present in groups.

Coffee Boiler 1

Is Not Heating

This message is displayed when the coffee boiler

does not reach the minimum temperature with the

programmed time interval.

See the parameter “Heating Timeout” for more information. The number on the display corresponds

to the number of the faulty coffee boiler.

Coffee Boiler 1

Overheated

This message is displayed when the coffee boiler

temperature exceeds the maximum allowed

temperature.

When this message is displayed call an authorized service technician to repair this fault. The also

CPU turns power off to the coffee boiler.

Steam Boiler
Probe Failed

This message is displayed when the CPU does not

detect the temperature probe.

When this message is displayed the CPU shuts down and turns off the machine.

The way to reset this error is to verify and to reconnect the temperature probe.

Steam Boiler

Overheated

This message is displayed when the steam boiler

temperature exceeds the maximum allowed

temperature.

When this message is displayed call an authorized service technician to repair this fault. The also

CPU turns power off to the steam boiler.

Steam Boiler

Is Not Heating

This message is displayed when the steam boiler

does not reach the minimum temperature with the

programmed time interval.

See the parameter “Heating Timeout” for more information.

«
...
107
108
109
110
111
...
»

Summary of Contents for Linea PB

















































































































Reviews:

No comments

Related manuals for Linea PB

Brand: Baratza Pages: 10

GOURMET 1000 TM/MD 8792

Brand: Bloomfield Pages: 24

Brand: Schaerer Pages: 34

Brand: Clatronic Pages: 50

Brand: Franke Pages: 2

DOMINATOR PLUS E3204

Brand: Falcon Pages: 6

Brand: Catler Pages: 16

ESPRESSO DELUXE

Brand: Gaggia Pages: 53

Brand: Magister Pages: 16

Brand: Ice-O-Matic Pages: 2

Brand: Ice-Tech Pages: 22

Brand: Keurig Pages: 7

Brand: Jura Pages: 13

Brand: Champion Pages: 12

Brand: LAVAZZA Pages: 88

Brand: SnackFood Pages: 6

Brand: RONDELL Pages: 20

Brand: RONDELL Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands