La Marzocco Linea PB Manual Download Page 102

Page: 102 / 112

102

Display

Operating Procedure

Description

Programming Mode

“Technical” Programming

After accessing the “Technical” programming menu and entering the password, use the buttons

and T2

until the following screen is displayed.

Press the T3 button

to enter the menu.

Move between the parameters using the buttons T1

and T2

to display the desired option:

Continuing to move with the buttons T1

and T2

you can display the total doses of each group.

Continuing to move with the buttons T1

and T2

you can also display the total doses of the tea button.

• This parameter allows the technician to

review the total doses.

• This parameter displays different values:
•

Total coffee doses;

•

Coffee doses for each group;

•

Tea doses.

Coffee Dose

Counter

Coffee Dose

Counter

Coffee Dose Counter

Total Coffee

Doses: 63

Enter Password

******

Doses G1

Tea Doses

“Technical” Programming

(only on MP espresso machine models)

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands