La Marzocco Linea PB Manual Download Page 73

Page: 73 / 112

Display

Operating Procedure

Description

Programming Mode

(only on ABR espresso machine models)

“Technical” Programming

Press the button T3

to exit the submenu.

Press T1

or T2

until the display shows the exit menu, press the T3 button

to return to the

“Technical” programming.

Press T1

or T2

to continue with the programming of the other parameters.

Press T2

and T3

at the same time to exit the programming mode and return to the normal use of the

espresso machine.

Exit

Group 1

Group Dose

Exit

LaMarzocco 00:00

CB 93.8

C SB

• This parameter allows the operator to

view and manually change each dose for
each key.

• For greater accuracy and consistency of

the doses, it is recommended that you
set each key.

• The dose can be set by pulses or by

mass (weight).

G1 Dose

Settings

Program Dose

Scales

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands