La Marzocco Linea PB Manual Download Page 99

Page: 99 / 112

Display

Operating Procedure

Description

Programming Mode

“Technical” Programming

Eco Mode
Settings

ECO Mode

• This parameter allows the technician to

set up a temperature to be maintained
in case of a temporary non utilization of
the espresso machine.

• It is possible to set this parameter also

during the normal operation of the
machine by pressing T1 and T2 at the

same time.

Press T1

or T2

to continue with the programming of the other parameters.

To exit the menu move between the parameters using the buttons T1

and T2

until the exit menu

is displayed. Press the T3 button

to exit the menu.

Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
by pressing T2

and T3

at the same time.

Exit

LaMarzocco 00:00

CB 93.8

C SB

Summary of Contents for Linea PB

















































































































Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands

La Marzocco Linea PB, Manual

Search results

Summary of Contents for Linea PB

Reviews:

Related manuals for Linea PB

Brands by name

Popular brands