JUKI AMS-221F3020RSW/AW-3 Page 2 Instruction Manual Download

Page: 2 / 163

CONTENTS

(WITH REGARD TO THE SEWING MACHINE) ......................................... 1

1. SPECIFICATIONS .......................................................................................................1
2. CONFIGURATION .......................................................................................................2
3. INSTALLATION ...........................................................................................................3

3-1. Removing the bed fixing bolt

......................................................................................... 3

3-2. Adjusting the safety switch ............................................................................................ 3

3-3. Installing the throat plate auxiliary cover (RSZ type)

.................................................. 4

3-4.

Preparation for the use of the AW-3 device

.................................................................. 5

3-4-1. Attaching / removing the AW-3 device cover .............................................................................5
3-4-2. Installing the feeding unit ...........................................................................................................6
3-4-3. Preparing the AW-3 ....................................................................................................................8

3-5. Installing the panel

......................................................................................................... 9

3-6. Installing the foot pedal

................................................................................................ 10

3-7. Installing the thread stand

........................................................................................... 11

3-8. Installing the air hose

................................................................................................... 12

3-9. Cautions for the compressed air supply (source of supply air) facility

.................. 13

3-10. Installing the eye protection cover

............................................................................ 14

3-11. Installing the cloth chip bag

....................................................................................... 14

3-12. Changing over the supply voltage

............................................................................ 15

4. PREPARATION OF THE SEWING MACHINE .......................................................... 17

4-1. Lubrication

.................................................................................................................... 17

4-2. Attaching the needle

..................................................................................................... 18

4-3. Threading the machine head

....................................................................................... 18

4-4. How to thread the device with the bobbin thread (RSZ type)

................................... 19

4-4-1. Installing and removing the bobbin case .................................................................................19
4-4-2. Installing the bobbin .................................................................................................................19

4-5. How to thread the device with the bobbin thread (RSW type)

.................................. 20

4-5-1. How to thread the device with the bobbin thread .....................................................................20

4-5-2. How to fit a bobbin in the bobbin case

.....................................................................................21

4-5-3. Length of remaining thread to be removed ..............................................................................22

4-6. Adjusting the thread tension

....................................................................................... 23

4-7. Intermediate presser height

......................................................................................... 24

4-8. Adjusting the thread take-up spring

........................................................................... 24

5. OPERATION OF THE SEWING MACHINE ............................................................... 25

5-1. Sewing ........................................................................................................................... 25

5-2. Needle thread clamp device

......................................................................................... 26

5-3. Bird’s nest reducing device

......................................................................................... 27

5-4. Adjusting the intermediate stop position of the feeding frame (left) (For the

separately-driven feeding frame with a double-stepped stroke function)

.................... 28

5-5. LED hand light

............................................................................................................... 29

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands