manualshive.com logo in svg

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Share
Download
JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download Page 155

– 150 –

Carry out the following steps of procedure to re-
place fuse 

❶

 of the device.

1)  Turn OFF the power switch and wait for five 

or more minutes.

2)  Remove the cover of control box for the de-

vice.

3)  Replace fuse 

❶

 attached on the PCB with a 

new one. Use the fuse with a specified capac

-

ity (125 V, T6A).

4)  Attach the cover removed in step 2) back in 

place.

❶

DANGER :

  In order to prevent accidents due to an electrical shock, be sure to turn OFF the power switch and 

remove the power plug from the receptacle before replacing the fuse. In addition, be sure to attach 

the rated fuse.

If the air tube at the gripper has worn out or is 
damaged, replace it with a spare tube supplied 
with the unit as an accessory following the steps 
of procedure described below.
1)  Detach hose nipple 

❶

 from the rear end of 

gripper. Then, detach the tube. 

2)  Detach the other end of tube from joint 

❷

.

3)  Connect a new tube following the afore-

mentioned steps of procedure in the reverse 
order.

CAUTION :

  Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of 

the sewing machine.

  In addition, close the air valve before replacing the tube.

2-2. Replacing the fuse

2-3. Replacing the gripper tube

❶

❷

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands