JUKI AMS-221F3020RSW/AW-3 Page 107 Instruction Manual Download

Page: 107 / 163

– 102 –

Ⓓ

: Threaded bobbin loading button

This button is used for loading a threaded bobbin
in the hook

❶

Ⓔ

: Nozzle air button

This button is used for operating nozzle air

❺

to feed thread

❹

from nozzle

❸

. Every time

Ⓔ

is pressed, nozzle air

❺

status will be changed over between "ON" and

"OFF".

Place the threaded bobbin at bobbin case standby
position

❷

. Press

Ⓓ

• If no bobbin is present in hook

❶

, the thread-

ed bobbin placed as described above will be
brought to hook

❶

. Then, the device waits

until next bobbin is placed at the bobbin case
standby position.

• If a threaded bobbin is present in hook

❶

the device will stand ready as it is.

Be sure to check the bobbin to be
loaded in the hook

❶

is wound

with thread before pressing

Ⓓ

. If an

empty bobbin is loaded in the hook

❶

, a malfunction can occur during

sewing.

❺

❹

❸

Be aware that the thread feed arm may operate when

Ⓔ

pressed.

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands