JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download

Page: 137 / 163

– 132 –

1-1. Adjusting the height of the needle bar (Changing the length of the needle)

* Turn ON the power once, and turn OFF the power again after making the intermediate presser

in the lowered state.

Bring needle bar

❶

down to the lowest position of its stroke. Loosen needle bar connection screw

❷

and adjust so that the upper marker line

❸

engraved on the needle bar aligns with the bottom end of

the needle bar bushing lower

❹

1. Maintenance of the sewing machine head

❶

❷

❺

: Marker line for DP×17 (with

needle count lower than #22)

1-2. Adjusting the needle-to-shuttle relation

* Turn ON the power once, and turn OFF the

power again after making the intermediate

presser in the lowered state.

III. MAINTENANCE OF SAWING MACHINE

After the completion of adjustment, turn the hand pulley to check to make sure that there
is no torque irregularity.

1) Loosen setscrews

❶

(right and left). Draw out

oil shield

❷

toward you to remove it.

2) Loosen hinge screw

❸

. Detach thread trim-

ming lever asm.

❹

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of

the sewing machine.

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of

the sewing machine.

❶

❺

❹

❸

❶

❷

❸

❹

3) Loosen four setscrews

❺

. Detach throat

plate asm.

❻

❺

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands