JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download

Page: 33 / 163

– 28 –

1) Loosen knob

❶

2) Adjust the intermediate stop position of the

feeding frame by turning knob

❷

so that it

stops slightly above the sewing product on
the machine.

Turning knob

❷

in direction

will increase

the height of the feeding frame in its inter-
mediate stop position or indirection

will

decrease it.

3) After the adjustment, securely tighten knob

❶

Only the feeding frame (left) is capa

ble of stopping in the intermediate
stop position.

❶

❷

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of

the sewing machine.

5-4. Adjusting the intermediate stop position of the feeding frame (left) (For the

separately-driven feeding frame with a double-stepped stroke function)

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands