JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download Page 60

Page: 60 / 163

– 55 –

2-4-8. How to use temporary stop

The sewing machine can be stopped by pressing
the temporary stop switch

❶

during sewing.

At this time, the error screen "E050: Temporary
stop error" is displayed to inform that the stop
switch has been pressed.

(1) To continue performing sewing from some point in sewing

①

Release the error

Press RESET button

to release the error.

When this error is reset, the thread trimming screen is dis-
played.

③

Adjust the presser to the re-sew

ing position

Press FEED FORWARD/BACKWARD
button

to move the feed-

ing frame to the re-sewing position.

②

Perform thread trimming

Press THREAD TRIM button

to perform thread trim-

ming.

When thread trimming is carried out, the sewing shape confir

mation screen is displayed.

* In the case the memory switch "U097: Temporary stop/thread

trimming operation" is set to the automatic thread trimming, the
sewing machine will automatically carry out thread trimming
and the THREAD TRIMMING button will not be displayed.

* If you press close button

on the thread trimming screen,

the shape confirmation screen will be displayed without per

forming thread trimming.

④

Re-start the sewing

When the pedal switch is depressed,
the sewing machine re-starts sewing.

❶

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Brands by name

Popular brands