JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download

Page: 106 / 163

– 101 –

❶

❷

Ⓐ

: Bobbin change button

This button is used for winding a bobbin with new
thread in the case of changing the thread, etc.
When

Ⓐ

is pressed, the

bobbin fitted

in hook

❶

is replaced by another

bobbin which is present at bobbin case standby
position

❷

. Then, the thread remaining on the

bobbin in hook

❶

is removed and new thread is

wound on the empty bobbin.

Ⓑ

: Bobbin take-out button

This button is used for taking out the bobbin load-
ed in hook

❶

. Take out the bobbin that is present

at bobbin case standby position

❷

by hand before

pressing

Ⓑ

. Then, when

Ⓑ

is pressed, the bobbin

loaded in hook

❶

is brought to bobbin case stand-

by position

❷

Place an empty bobbin at bobbin case standby position

❷

and press

Ⓒ

• If no bobbin is present in hook

❶

, the empty bobbin placed as described above will be brought

to hook

❶

. Then, the device waits until the display is restored to the previous one and the

next bobbin is placed. The device starts winding a bobbin when

Ⓒ

Ⓓ

is pressed after placing the next bobbin in the hook

❶

• If a bobbin is already present in hook

❶

, the device will start winding of the bobbin.

Be sure to check that the bobbin to be loaded in the hook

❶

is empty before pressing

Ⓒ

. If a threaded bobbin is loaded in the hook

❶

, a malfunction

can occur when winding the bobbin or removing the thread remaining on the bobbin.

Ⓒ

: Empty bobbin loading button

This button is used for loading an empty bobbin in the hook

❶

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands