JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download

Page: 76 / 163

– 71 –

Button and display

Description

FEEDING FRAME INITIAL
POSITION button

When this button is pressed while the sewing machine temporarily stops sewing, the
feeding frame is returned to the start of sewing and is lifted.

CURRENT STEP
CHANGEOVER button (+)

Step to be sewn can be proceeded to the next one with this button.

CURRENT STEP
CHANGEOVER button (-)

Step to be sewn can be returned to the previous one with this button.

1-STEP REPEAT button

Enable/disable of the 1-step repeat is selected with this button
When the 1-step repeat is set to "enable", the current step can be sewn in
repetition even when sewing of the current step is completed.

SPEED variable resistor

Number of rotations of the sewing machine can be changed.

File name display

File name of the selected pattern is displayed.

Comment display

Comment for the selected pattern is displayed.

MULTIFUNCTION TAB
SELECTION button

Tab display can be changed over on a function-by-function basis with this button.

→

Refer to

"II-2-4-3. Multifunction tab display" p.41

2-5-3. How to create a new cycle pattern

①

Displaying the new cycle pattern creation screen

When the NEW CYCLE PATTERN CREATION button

is pressed on the pattern setting screen or the cycle pattern
setting screen, the new cycle pattern creation screen is dis-
played.

A new cycle pattern is created.

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands