background image

Before you get started, check to see that you have

all the parts listed below.  Read all directions before

starting any assembly.

Parts Shown in Figure 1:

-

 Switchbox Power Unit w/10’ Battery Cable, 1 ea.

-

 Tank Stand, 1 ea.

-

 2 qt. Tank, 1 ea.

-

 Cap Assembly, 1 ea.

-

 Foam Tubing Elbows, 2 ea.

-

 Collector Heads, 2 ea.

Parts Not Shown in Figure 1:

* Foam Tubing Tee, 1 ea.

1” Sections of Velcro, 4 ea.

*

 15’ Section of Vinyl Foam Tubing, 1 ea.

*

 10’ Section of Air Tubing, 1 ea.

Cable Ties, 12 ea.

1.  Attach the Tank Stands

Determine a convenient location to bolt the tank stand,

keeping in mind that the tank should be mounted near

the back of the applicator and be kept in a perpendicular

position.  The stand is designed to facilitate many different

mounting configurations.  Often times, the bracket will

easily mount on a horizontal frame member on the applica-

tor.  Attach the tank stand to the applicator using U-bolts

or hex-head bolts as needed (not supplied).

2.  Set Tank in Stand

Place the tank in the tank stand and secure the cap

assembly.

3.  Attach Power Unit Switchbox

Determine a convenient location to place the power

unit switchbox for ease of turning on and off.  Either bolt

the box down or attach using the 1” velcro strips provided.

Secure firmly in place as needed.  Route the battery cable

to the battery and secure the red wire to the positive (+)

battery post.  Secure the white wire to the negative (-)
battery post.

4.  Install Air Tubing

Using the smaller diameter air tubing, connect the tubing
to the outlet on the back of the switchbox assembly and
route back to the tank.  Connect to the small inlet on the
top of the cap assembly.  Secure tubing as needed with the
cable ties provided.

FIGURE 1: Parts Diagram

5. Install Foam Tubing

Cut a length of the larger diameter tubing equal to the desired
drop width of the applicator, then cut this length of tubing in
half.  (For example, if the applicator’s spray width if 90 inches,
first cut a 90” section, then cut this section into two 45”
pieces.)  Install the foam tubing tee to connect the two pieces
of tubing, then mount this assembly to the spray boom using
the cable ties provided.  Next, cut and install a length of tubing
to connect the cap assembly outlet on the tank to the foam
tubing tee on the spray boom.  Cut two additional lengths of
tubing to use as drop tubes at the end of the tubing assembly.
When positioned and cut correctly, the drop tubes should be
about 6 inches above the applicaton canopy to prevent the
foam drops from blowing off course.  Insert the foam tubing
elbows into the foam tubing at the end of each boom  Insert
the drop tubes into the foam tubing elbows.  Insert collector
heads into the bottom of the drop tubes.

For single drop applications, cut a length of tubing to connect
to the cap assembly outlet on the tank and the desired foam
drop location.  Install the collector head and secure with cable
ties as needed.

      T

T

T

T

TurfT

urfT

urfT

urfT

urfTrrrrrac

ac

ac

ac

ack

kk

kker  3301 

er  3301 

er  3301 

er  3301 

er  3301 Assemb

Assemb

Assemb

Assemb

Assembllllly Instr

y Instr

y Instr

y Instr

y Instructions:

uctions:

uctions:

uctions:

uctions:

TM

FOAM

MARKER

ON

OFF

LEFT

RIGHT

RICHWAY

ON

OFF

TurfTracker

Switchbox 

   Power 

    Unit

 Foam

Tubing

Elbows

Collector

  Heads

 Tank

Stand

    Cap

Assembly

Tank

TO USE YOUR NEW TURF TRACKER 3301
FOAM MARKING SYSTEM:

Your 

TurfTracker

 3301 Foam Marking System

is designed to operate with liquid dishwashing soap
and distilled water.  The operator may need to alter
mix rates and products used to get the desired
results.

1.  Add Distilled Water

Fill the tank ¾ full with distilled water.  The manufac-
turer recommends using distilled water- use of any
other water source may decrease performance of the
unit.  Overfilling the tank will initially decrease
performance.

2.  Measure & Add Liquid Dishwashing Soap

Add 1-3 Tbls. of liquid dishwashing soap to
the water.  It is recommended that you first
mix 1 Tbls. of soap and check the foam output
of the unit.  Increase soap concentration as needed
to get the desired foam output.  Performance of
the foam marking unit may vary with different
kinds of dishwashing soap.  If foam output is poor,
try a different kind of soap.  

This unit is designed

for LIQUID dishwashing soap.

3.  Shake Bottle

Replace the cap assembly onto the tank, making
certain the cap gasket is in place.  Shake the bottle a
few times and return assembly to the tank stand.
Reattach the hoses.

4.  Run for 30 Seconds

Turn on the power unit and let run for 30
seconds until foam output is consistent.
Begin fertilizing with your new foam marking
system.  Remember that the marker is marking
the edge of your lawn treatment, not your
wheel tracks.  Adjust your treatment path to
eliminate unsightly skips and overlaps.

    Instructions Continued on Back Panel

 Tank
Stand

Assembly

Reviews: