background image

– 5 –

Within 0.3 mm

 

1.  Fix the throat plate auxiliary 

cover 

 so that is higher than 

the throat plate 

 (within 0.3 

mm). When it is lower than 
the throat plate 

, needle 

breakage or the like due to the 
defective feed will be caused.

 

2.  Confirm by putting a ruler or 

the like that the throat plate 
auxiliary cover 

 is horizon

-

tally installed. If not, throat 
plate auxiliary cover 

 and 

lower plate 

 come in contact 

partially with each other, and 
abnormal worn-out will be 

caused.

3-4-1. 

Attaching / removing the AW-3 device cover

It is necessary to remove the front cover 

 in order to set up the bobbin thread or carry out mainte-

nance. Remove the cover 

 as described below.

1)  Loosen six setscrews 

 on the right and left side faces of the AW-3 device.

2)  Slightly shift the cover 

 upward, then carefully draw it toward you.

 

Install the cover 

 reversing the removal procedure.

Be sure to attach cover 

 for the sake of safety when performing sewing.

WARNING :

  In the case you use the AMS-221F

△△

3020RSW (provided with AW-3 device) model of sewing ma

-

chine, detach the cover and carry out preparation for the use of the AW-3 device. 

  The AW-3 device uses an optical sensor. In order to protect the AW-3 device against malfunction, 

neither install the AW-3 device at any place that is exposed to direct sunlight such as a window side 

nor orient it to such a direction that it is exposed to direct sunlight.

3-4. 

Preparation for the use of the AW-3 device

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Reviews: