INVT Goodrive GD300-19-004G-4 Operation Manual Download Page 247

Page: 247 / 255

Goodrive300-19 series open loop vector inverter special for hosit Peripherial options and parts

-246-

necessary to add reactor compensation. If the distance between the inverter and motor is 50~100m,

see the table below for model selection; if it exceeds 100m, consult with INVT technical support.

The inverters of 380V (

≥75kW) can be equipped with external DC reactors for the improvement of

power factors and the avoidance of damage from high input current to the rectifying components

because of the high-capacity transformer. The device can also cease the damage to the rectifying

components which are caused by supply net voltage transients and harmonic waves of the loads.

C.6.1 AC 3PH 380V(-15%)~440V(+10%)

Inverter model

Input reactor

DC reactor

Output reactor

GD300-19-1R5G-4

ACL2-1R5-4

OCL2-1R5-4

GD300-19-2R2G-4

ACL2-2R2-4

OCL2-2R2-4

GD300-19-004G-4

ACL2-004-4

OCL2-004-4

GD300-19-5R5G-4

ACL2-5R5-4

OCL2-5R5-4

GD300-19-7R5G-4

ACL2-7R5-4

OCL2-7R5-4

GD300-19-011G-4

ACL2-011-4

OCL2-011-4

GD300-19-015G-4

ACL2-015-4

OCL2-015-4

GD300-19-018G-4

ACL2-018-4

OCL2-018-4

GD300-19-022G-4

ACL2-022-4

OCL2-022-4

GD300-19-030G-4

ACL2-030-4

OCL2-030-4

GD300-19-037G-4

ACL2-037-4

OCL2-037-4

GD300-19-045G-4

ACL2-045-4

OCL2-045-4

GD300-19-055G-4

ACL2-055-4

OCL2-055-4

GD300-19-075G-4

ACL2-075-4

DCL2-075-4

OCL2-075-4

GD300-19-090G-4

ACL2-090-4

DCL2-090-4

OCL2-090-4

GD300-19-110G-4

ACL2-110-4

DCL2-110-4

OCL2-110-4

Summary of Contents for Goodrive GD300-19-004G-4
































































































































































































































































Search results

Summary of Contents for Goodrive GD300-19-004G-4

Reviews:

Brands by name

Popular brands

INVT Goodrive GD300-19-004G-4, Operation Manual

Search results

Summary of Contents for Goodrive GD300-19-004G-4

Reviews:

Brands by name

Popular brands