manualshive.com logo in svg

INVT Goodrive GD300-19-004G-4, Operation Manual

Share
Download
INVT Goodrive GD300-19-004G-4 Operation Manual Download Page 198

Goodrive300-19 series open loop vector inverter special for hosit                                        Fault tracking

 

-197- 

8.6.2 Motor vibration 

Motor vibration or 

abnormal noise 

Check the motor parameter 

or motor type is right or not 

If it is the inverter fault, 

please contact with our 

company

Check if there is abnormal 

fluctuation to the load

Check if there is abnormal 

vibration to frequency 

reference

Check the speed loop and 

current loop are right or not

Vector control or not 

Perform parameter 

autotune or not 

Please set right 

motor type and 

parameters 

Perform right 

parameter autotune

Set right 

parameters

Set right V/F vibration 

parameter or not 

Set right parameter

Check frequency 

reference

Check the load 

Yes 

No 

Yes 

No 

Yes 

No 

Yes 

No 

Yes 

No 

Yes 

No 

Yes 

No 

 

Summary of Contents for Goodrive GD300-19-004G-4
































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands