INVT Goodrive GD300-19-004G-4 Operation Manual Download Page 240

Page: 240 / 255

Goodrive300-19 series open loop vector inverter special for hosit Peripherial options and parts

-239-

Peripherial options and parts Appendix C

C.1 What this chapter contains

This chapter describes how to select the options and parts of Goodrive300-19 series.

C.2 Peripherial wiring

Below is the peripherial wiring of Goodrive300-19 series inverters.

Note:

1. The inverters (

≤55kW) are embedded with braking unit.

2. The inverters (

≥75kW) have P1 terminal and can be connected with external DC reactors.

3. The braking units apply standard braking units. Refer to the instruction of DBU for detailed

information.

Summary of Contents for Goodrive GD300-19-004G-4
































































































































































































































































Search results

Summary of Contents for Goodrive GD300-19-004G-4

Reviews:

Brands by name

Popular brands

INVT Goodrive GD300-19-004G-4, Operation Manual

Search results

Summary of Contents for Goodrive GD300-19-004G-4

Reviews:

Brands by name

Popular brands