background image

Chapter 4: Commands for CLI configuration 

ip igmp ssm-range 

Command:  

ip igmp ssm-range <ipv4_mcast> <Ipv4PrefixLength : 4-32>  

    

ip          

Internet Protocol 

igmp       

Internet Group Management Protocol 

    ssm-range       

IPv4 address range of Source Specific Multicast 

<ipv4_mcast>   

 Valid IPv4 multicast address 

<vlan_list>

    VLAN identifier(s): VID 

<Ipv4PrefixLength : 4-32>

    Prefix length ranges from 4 to 32 

Default:    

232.0.0.0/8 

Usage Guide:  

To enable 

SSM Range

 of 

IGMP. 

 

Example:  

To enable 

SSM Range

 (239.239.239.239/32) of 

IGMP.

 

 

Switch# configure terminal 
Switch (config)#

 ip igmp ssm-range 239.239.239.239 32

 

ip igmp unknown-flooding 

Command:  

ip igmp unknown-flooding 

    

ip         

Internet Protocol 

igmp      

Internet Group Management Protocol 

unknown-flooding    

Flooding unregistered IPv4 multicast traffic 

 

Default:    

Enabled 

Usage Guide:  

To flood unregistered 

IPv4 multicast 

traffic

 

 
Example:  

To flood unregistered 

IPv4 multicast 

traffic

 

Switch# configure terminal 
Switch (config)#

 ip igmp unknown-flooding

 

ip name-server 

Command:  

ip name-server <ipv4_ucast> 

    

ip        

 Internet Protocol 

name-server     

Domain Name System 

<ipv4_ucast>   

 A valid IPv4 unicast address 

Default:    

144 

NS3500-24T-4C Managed Switch Command Guide 

Summary of Contents for NS3500-24T-4C







































































































































































































































































































































Reviews: