Interlogix NS3500-24T-4C Command Manual Download

Page: 44 / 326

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)#

dot1x authentication timer re-authenticate 777

dot1x guest-vlan

Command:

dot1x guest-vlan <1-4095>

<1-4095>

Guest VLAN ID used when entering the Guest VLAN

Default:

Usage Guide:

To set the value of

guest-vlan

for

Network Access Server

Example:

To set the value of

guest-vlan(2)

for

Network Access Server

Switch# configure terminal
Switch (config)#

dot1x guest-vlan 2

dot1x guest-vlan supplicant

Command:

dot1x guest-vlan supplicant

supplicant

The switch remembers if an EAPOL frame has been received on the port

for the life-time of the port. Once the switch considers whether to enter
the Guest VLAN, it will first check if this option is enabled or disabled.

Default:

Disable

Usage Guide:

To allow all frames automatically entering

guest-vlan

for

Network Access Server

Example:

To allow all frames automatically entering

guest-vlan

for

Network Access Server

Switch# configure terminal
Switch (config)#

dot1x guest-vlan supplicant

dot1x max-reauth-req

Command:

dot1x max-reauth-req <1-255>

Default:

Usage Guide:

NS3500-24T-4C Managed Switch Command Guide

Summary of Contents for NS3500-24T-4C







































































































































































































































































































































Search results

Summary of Contents for NS3500-24T-4C

Reviews:

Related manuals for NS3500-24T-4C

Brands by name

Popular brands

Interlogix NS3500-24T-4C, Command Manual

Search results

Summary of Contents for NS3500-24T-4C

Reviews:

Related manuals for NS3500-24T-4C

Brands by name

Popular brands