Interlogix NS3500-24T-4C Command Manual Download

Page: 26 / 326

Chapter 4: Commands for CLI configuration

clear mac address-table

Command:

clear mac address-table

Default:

N/A

Usage Guide:

To clear the mac address-table.

Example:

To clear the Switch’s

mac address-table.

Switch# clear mac address-table

clear mep

Command:

clear mep <Inst : uint>

<Inst : uint> The MEP instance.

Default:

N/A

Usage Guide:

To clear the MEP instance profiles.

clear mvr name

Command:

clear mvr name <MvrName : word16>

<MvrName : word16> MVR multicast VLAN name

Default:

N/A

Usage Guide:

To clear the mvr name profiles.

clear mvr statistics

Command:

clear mvr statistics

Default:

N/A

Usage Guide:

To clear the mvr statistics.

Example:

To clear the Switch’s

mvr statistics.

NS3500-24T-4C Managed Switch Command Guide

Summary of Contents for NS3500-24T-4C







































































































































































































































































































































Search results

Summary of Contents for NS3500-24T-4C

Reviews:

Related manuals for NS3500-24T-4C

Brands by name

Popular brands

Interlogix NS3500-24T-4C, Command Manual

Search results

Summary of Contents for NS3500-24T-4C

Reviews:

Related manuals for NS3500-24T-4C

Brands by name

Popular brands