Intel i960 Jx Developer'S Manual Download Page 416 | Manualshive

Page: 416 / 578

background image

MEMORY CONFIGURATION

13-2

13.1.2

Logical Memory Attributes

The i960 Jx provides a mechanism for defining two logical memory templates (LMTs). An LMT
may be used to specify the logical memory attributes for a section (or subset) of a physical
memory subsystem connected to the BCU (e.g., DRAM, SRAM). The logical memory attributes
defined by the i960 Jx are byte ordering and whether the information is cacheable or
non-cacheable in the on-chip data cache.

There are typically several different LMTs defined within a single memory subsystem. For
example, data within one area of DRAM may be non-cacheable while data in another area is
cacheable.

Figure 13-1

shows the use of the Control Table (PMCON registers) with logical

memory templates for a single DRAM region in a typical application.

Figure 13-1. PMCON and LMCON Example

PMCON Registers

Region 14_15

Region 12_13

Region 10_11

Region 8_9

Region 6_7

Region 4_5

Region 2_3

Region 0_1

8000 0000H

FFFF FFFFH

Physical

Regions 10_11

0000 0000H

Logical Memory

Templates

(LMCON)

LMADR0

LMMAR0

LMADR1

LMMAR1

Non-Cacheable

Physical

Region 8_9

Physical

Regions 0_1

9FFF FFFFH

Non-Cacheable

32-bit wide

DRAM

Note: DLMCON maps the remaining memory to cacheable.

to 14_15

to 6_7

«
...
414
415
416
417
418
...
»

Summary of Contents for i960 Jx



































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i960 Jx

Brand: VAF instruments Pages: 56

Brand: Grundig Pages: 24

Brand: Cervoz Pages: 22

Quadro M6000 Sync

Brand: Nvidia Pages: 8

SiliconDrive SSD-P16G(I)-3100

Brand: Silicon Systems Pages: 108

Brand: AXAGO Pages: 2

Brand: Hauppauge Pages: 55

Brand: Omron Pages: 29

Brand: Altera Pages: 33

Brand: Omron Pages: 432

Brand: Aerotech Pages: 62

Brand: Roland Pages: 224

Brand: ADLINK Technology Pages: 69

Brand: silicom Pages: 16

VDA-NVR2108W4KS2

Brand: Dahua Technology Pages: 363

IQ Switch IQS128

Brand: Azoteq Pages: 4

Brand: Orcomm Pages: 10

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands