manualshive.com logo in svg

Intel i960 Jx, Developer'S Manual, Page: 388 / 578

Share
Download
Intel i960 Jx Developer'S Manual Download Page 388

INITIALIZATION AND SYSTEM REQUIREMENTS

12-18

12.3.2

Process PRCB Flow

The following pseudo-code flow illustrates the processing of the PRCB. Note that this flow is used
for both initialization and reinitialization (through

 sysctl

).

Example 12-2.  Process PRCB Flow 

Process_PRCB(prcb_ptr)

{  PRCB_mmr = prcb_ptr;

   reset_state(data_ram); /* It is unpredictable whether the   */

                     /* Data RAM keeps its prior contents */

    fault_table  =  memory[PRCB_mmr];

    ctrl_table   =  memory[P0x4];

    AC           =  memory[P0x8];

    fault_config =  memory[P0xc];

        if (1 & (fault_config >> 30)) generate_fault_on_unaligned_access = false;

        else                          generate_fault_on_unaligned_access = true;

/** Load Interrupt Table and Cache NMI Vector Entry in Data RAM**/  

    Reset_block_NMI;

    interrupt_table =  memory[P0x10];

    memory[0] = memory[interrupt (248*4) + 4];

/** Process System Procedure Table **/

    sysproc = memory[P0x14];

    temp    = memory[0xc];

    SSP_mmr = (~0x3) & temp;

    SSP.te  = 1 & temp;

/** Initialize ISP, FP, SP, and PFP **/

    ISP_mmr =  memory[P0x1c];

    FP      = (~0xF) & ISP_mmr;

    SP      = FP + 64;

    PFP     = FP;

/** Initialize Instruction Cache **/

    ICCW = memory[P0x20];

    if (1 & (ICCW >> 16) ) disable(I_cache);

/** Configure Local Register Cache **/

    programmed_limit = (7 & (memory[P0x24] >> 8) );

    config_reg_cache( programmed_limit );

/** Load_control_table. **/

    load_control_table(ctr0x10 , ctr0x58);

    load_control_table(ctr0x68 , ctr0x6c);

    IBP0 = 0x0; IBP1 = 0x0; DAB0 = 0x0; DAB1 = 0x0; BPCON = 0x0

/** Initialize Timers **/

    TMR0.tc   = 0; TMR1.tc   = 0; TMR0.enable = 0; TMR1.enable = 0;

    TMR0.sup  = 0; TMR1.sup  = 0; TMR0.reload = 0; TMR1.reload = 0;

    TMR0.csel = 0; TMR1.csel = 0;

    DLMCON.dcen = 0

    LMMR0O.lmte = 0

    LMMR1.lmte = 0

    return;

}

Summary of Contents for i960 Jx



































































































































































































































































































































































































































































































































































































Reviews:

No comments