manualshive.com logo in svg

Intel i960 Jx, Developer'S Manual, Page: 328 / 578

Share
Download
Intel i960 Jx Developer'S Manual Download Page 328

INTERRUPTS

11-2

Since interrupts are handled based on priority, requested interrupts are often saved for later service
rather than being handled immediately. The mechanism for saving the interrupt is referred to as
interrupt posting. Interrupt posting is described in 

section 11.6.5, “Posting Interrupts” (pg. 11-9)

.

The i960 core architecture defines two data structures to support interrupt processing: the interrupt
table (see 

Figure 11-1

) and interrupt stack. The interrupt table contains 248 vectors for interrupt

handling procedures (eight of which are reserved) and an area for posting software-requested
interrupts. The interrupt stack prevents interrupt handling procedures from using the stack in use
by the application program. It also allows the interrupt stack to be located in a different area of
memory than the user and supervisor stack (e.g., fast SRAM).

Figure 11-1.  Interrupt Handling Data Structures

11.1.1

The i960

®

 Jx Processor Interrupt Controller

The i960 Jx processor Interrupt Controller Unit (ICU) provides a flexible, low-latency means for
requesting and posting interrupts and minimizing the core’s interrupt handling burden. Acting
independently from the core, the interrupt controller posts interrupts requested by hardware and
software sources and compares the priorities of posted interrupts with the current process priority.

The interrupt controller provides the following features for managing hardware-requested interrupts:

•

Low latency, high throughput handling

•

Support of up to 240 external sources

•

Eight external interrupt pins, one non-maskable interrupt pin, two internal timers sources for
detection of hardware-requested interrupts

•

Edge or level detection on external interrupt pins

•

Debounce option on external interrupt pins

The user program interfaces to the interrupt controller with six memory-mapped control registers.
The interrupt control register (ICON) and interrupt map control registers (IMAP0-IMAP2)
provide configuration information. The interrupt pending (IPND) register posts
hardware-requested interrupts. The interrupt mask (IMSK) register selectively masks
hardware-requested interrupts.

Interrupt 

Interrupt

Table 

Handling

Procedure

Interrupt
Request

Interrupt Pointer

Memory

i960

®

 Jx 

Processor

Summary of Contents for i960 Jx



































































































































































































































































































































































































































































































































































































Reviews:

No comments