manualshive.com logo in svg

Intel i960 Jx, Developer'S Manual, Page: 91 / 578

Share
Download
Intel i960 Jx Developer'S Manual Download Page 91

INSTRUCTION SET OVERVIEW

5-5

5

5.2.1

Data Movement

These instructions are used to:

•

move data from memory to global and local registers

•

from global and local registers to memory

•

between local and global registers

Rules for register alignment must be followed when using load, store and move instructions that
move 8, 12 or 16 bytes at a time. See 

section 3.5, “MEMORY ADDRESS SPACE” (pg. 3-13)

 for

alignment requirements for code portability across implementations.

5.2.1.1

Load and Store Instructions

Load instructions copy data from memory to local or global registers. Each load instruction has a
corresponding store instruction to memory. All load and store instructions use the MEM format.

ld

 copies 4 bytes from memory into a register; 

ldl

 copies 8 bytes into 2 successive registers; 

ldt

copies 12 bytes into 3 successive registers; 

ldq

 copies 16 bytes into 4 successive registers.

st

 copies 4 bytes from a register into memory;

 stl

 copies 8 bytes from 2 successive registers; 

stt

copies 12 bytes from 3 successive registers; 

stq

 copies 16 bytes from 4 successive registers.

For 

ld

, 

ldob

, 

ldos

, 

ldib

 and 

ldis

, the instruction specifies a memory address and register; the

memory address value is copied into the register. The processor automatically extends byte and
short (half-word) operands to 32 bits according to data type. Ordinals are zero-extended; integers
are sign-extended.

ld

load word

st

store word

ldob

load ordinal byte

stob

store ordinal byte

ldos

load ordinal short

stos

store ordinal short

ldib

load integer byte

stib

store integer byte

ldis

load integer short

stis

store integer short

ldl

load long

stl

store long

ldt

load triple

stt

store triple

ldq

load quad

stq

store quad

Summary of Contents for i960 Jx



































































































































































































































































































































































































































































































































































































Reviews:

No comments