Intel i960 Jx Developer'S Manual Download Page 558 | Manualshive

Page: 558 / 578

background image

GLOSSARY

Glossary-6

RIP

See Return Instruction Pointer.

Software Reset

Re-running of the Reset microcode without physically asserting the
RESET# pin or removing power from the CPU.

SP

See Stack Pointer.

Special Function
Registers (SFRs)

A 32-bit register (sf0-sf4) used to control specific sections of the
processor. These registers can be manipulated like any other register, but
their contents affect the processor’s behavior directly.

Stack Frame

A block of bytes on a stack used to store local variables for a specific
procedure. Another term for a stack frame is an activation record. Each
procedure that the processor calls has its own stack frame associated with
it. A stack frame is always aligned on a 64-byte boundary. The first 64
bytes in a stack frame are reserved for storage of the local registers
associated with the procedure. The frame pointer (FP) and stack pointer
(SP) for a particular frame indicate location and boundaries of a stack
frame within a stack.

Stack Pointer (SP)

The address of the last byte in the current (topmost) frame of the
procedure stack. The SP is contained in local register r1.

Stack

A contiguous array of bytes in the address space that grows from low
addresses to high addresses. It consists of contiguous frames, one frame
for each active procedure. i960 architecture defines three stacks: local,
supervisor and interrupt.

State Flag

PC register bit 10. This flag indicates to software that the processor is
currently executing a program (0) or servicing an interrupt (1).

State

The type of task that the processor is currently working on: a program or
an interrupt handling procedure. The processor sets the PC register state
flag to indicate its current state.

Status and Control
Registers

A set of four 32-bit registers that contain status and control information
used in controlling program flow. These registers include the instruction
pointer (IP), AC register, PC register and TC register.

Supervisor Call

A system call (made with the

calls

instruction) where the entry type of

the called procedure is 102. If the processor is in user mode when a
supervisor call is made, it switches to the supervisor stack and to
supervisor mode.

Supervisor Mode

One of two execution modes – user and supervisor – that the processor
can use. The processor uses the supervisor stack when in supervisor
mode. Also, while in supervisor mode, software is allowed to execute
supervisor mode instructions such as

sysctl

and

modpc

.

«
...
556
557
558
559
560
...
»

Summary of Contents for i960 Jx



































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i960 Jx

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP DAS USA Pages: 8

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: Palo Alto Network Pages: 56

Millennium P650

Brand: Matrox Pages: 54

Brand: T.A Pages: 11

Brand: ACTi Pages: 12

Brand: H3C Pages: 34

EK-Quantum Vector FTW3 RTX 2080 Ti

Brand: ekwb Pages: 3

Brand: Xilinx Pages: 43

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

Brand: Rimage Pages: 30

Brand: Cypress Semiconductor Pages: 32

DMX-Relais 2 INRUSH

Brand: DMX4ALL Pages: 18

Brand: ICP DAS USA Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands