Huawei FusionModule500 User Manual Download Page 74 | Manualshive

Page: 74 / 302

background image

●

If the cabinet installation environment is in poor condition, to well store the

cabinet after it is unpacked, take measures to prevent dust. You can wrap the

cabinet with the original plastic coat.

NO TICE

Do not tear down the transparent film from the glass door during the installation.

The film will be removed after the entire module is installed.

Procedure

Step 1 Use a pallet truck to transport the cabinet to the installation position.
Step 2 Check that the cabinet package is intact.
Step 3 Cut off and remove the binding straps, and remove the packing.
Step 4 Remove pallets from ordinary cabinets.

1. Remove the plastic bag and take out the fitting box.
2. Check the cabinet exterior for damage. If any damage is found, notify the

carrier immediately.

3. Check against the packing list that the equipment and fittings are correct and

complete. If some fittings are missing or do not comply with the packing list,

record the information and contact your local Huawei office immediately.

4. After checking that the cabinet is intact, remove the screw assemblies that

secure the cabinet to the pallet, as shown in

NO TICE

Set the screw assemblies aside for they will be used in installation steps.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

Copyright © Huawei Technologies Co., Ltd.

64

«
...
72
73
74
75
76
...
»

Summary of Contents for FusionModule500















































































































































































































































































































Reviews:

No comments

Related manuals for FusionModule500

ebro EBI 10 Series

Brand: Xylem Pages: 48

Telemotive blue PiraT Mini

Brand: Magna Pages: 60

Brand: Emerson Pages: 9

Brand: BLUE INK TECH Pages: 39

Brand: ADTEK Pages: 8

EASYLOG 80NS Series

Brand: GHM Greisinger Pages: 16

Brand: Agilent Technologies Pages: 169

Brand: Radionode Pages: 23

Brand: YOKOGAWA Pages: 129

Brand: EasyLog Pages: 2

Brand: Campbell Pages: 26

Brand: Jamar Pages: 56

Brand: SS Telecoms Pages: 26

Brand: SATO Pages: 2

Brand: ZyAura Pages: 3

Brand: Elseta Pages: 160

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands