Huawei FusionModule500 User Manual Download Page 111

Page: 111 / 302

Figure 4-41 Installing a lithium battery

NO TICE

● The lithium battery weighs about 43 kg. Check the load-bearing capability of

the rack tray before installation.

● The lithium battery is 396 mm deep. Check the depth of the rack before

installation.

● The lithium battery can be installed in a 19-inch rack with guide rails and a

tray. Check whether the load-bearing capability meets requirements.

● If multiple lithium batteries are installed, certain clearances should be reserved.

The space for each lithium battery should be at least 3 U. The lithium batteries

cannot be directly stacked or vertically placed.

● Install lithium batteries from bottom to top.

Step 2 Install the protective covers for the positive and negative poles of the lithium

batteries.

Step 3 Install other lithium batteries in the same way.

----End

4.2.5.2 (Optional) Installing Busbars

Prerequisites

If there is more than one lithium battery, install busbars.

Install busbars before installing the PDU2000.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

101

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands