Huawei FusionModule500 User Manual Download Page 58

Page: 58 / 302

Category

Item

Specifications

Dimensions

(H x W x

86 mm x 442 mm x 467 mm

3.4.3.3.3 (Optional) VCN510

Figure 3-18 Appearance

Table 3-33 Performance specifications

Item

Specifications

Device access and video storage

Supports a maximum of eight video

access channels or 128 Mbit/s video

access bandwidth.

Video forwarding

Supports a maximum of 32 video

forwarding channels or 256 Mbit/s

video forwarding bandwidth.

Video playback and download

Supports a maximum of eight video

playback and download channels or

128 Mbit/s video playback and

download bandwidth.

Ingress and egress bandwidth

The ingress bandwidth does not

exceed 128 Mbit/s.
The egress bandwidth does not exceed

256 Mbit/s.

Table 3-34 Hardware specifications

Item

Specifications

Number of disks

Whether the hard disk supports hot

swap

Supported hard disk type

3 TB, 4 TB, 6 TB, or 8 TB SATA disks

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands