manualshive.com logo in svg

Huawei FusionModule500, User Manual

Share
Download
Huawei FusionModule500 User Manual Download Page 186

6. Set Leak sensor to Enable and click Submit.
7. Set Leak sensor type to Leak sensor(Electroc) and click Submit.

Step 2 Check functions of water sensors.

Table 5-10 Function check

Check Method

Normal Connection Status

Alarm Clearance Method

Immerse the two

contacts of the

electrode water

sensor in water.

Leak DI alarm is generated

on the active alarm screen of

the app or on the WebUI.

Wipe dry the two contacts of

the water sensor. The alarm

disappears automatically.

 

----End

5.3.9 Commissioning a Cabinet Electronic Clasp Lock

Prerequisites

The cabinet door can be opened and closed properly. If the cabinet door cannot be

opened and closed properly, adjust the position of the cabinet electronic clasp lock

by performing steps 1 and 2.

Procedure

Step 1 (Optional) Check whether the cabinet door lock is leveled to 2000 (+3) mm. If

not, adjust it.

Step 2 (Optional) If the cabinet door still cannot be opened after step 1 is performed,

adjust the position of the cabinet electronic clasp lock by using the slotted holes

until the cabinet door can be opened and closed properly.

Step 3 Set device addresses for cabinet electronic clasp locks.

●

A cabinet electronic clasp lock is installed at the front and rear doors of the

cabinet respectively. The address for the cabinet electronic clasp lock on the

front door is an odd number, and that for the cabinet electronic clasp lock on

the rear door is an even number.

●

Set a device address for a cabinet electronic clasp lock by operating the toggle

switch on the cabinet electronic clasp lock. Toggle switches 1 to 6 specify the

device address in binary mode. ON indicates 1, and OFF indicates 0.

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

Copyright © Huawei Technologies Co., Ltd.

176

Summary of Contents for FusionModule500















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands