Huawei FusionModule500 User Manual Download

Page: 184 / 302

Check Method

Normal Connection Status

Set T/H sensor alarm

thresholds.

Choose Monitoring > Aisle > T/H Sensor Group

> T/H Sensor n > Running Parameters and set

High temperature alarm threshold, Low

temperature alarm threshold, High humidity

alarm threshold, and Low humidity alarm

threshold as required.

NOTE

The default values of High temperature alarm

threshold, Low temperature alarm threshold, High

humidity alarm threshold, and Low humidity alarm

threshold are 35.0°C, 5.0°C, 85.0% RH, and 15.0%

RH respectively.

----End

5.3.8.3 Commissioning the WLDS900 Water Sensor

If a water sensor is installed, perform the following steps to configure it.

Prerequisites

One end of the straight-through cable has been connected to the RJ45 port on the

WLDS900 water sensor, and the other end has been connected to the AI/DI_2 port

on the ECC800-Pro.

Context

●

To use the AI/DI sensor, enable the corresponding AI/DI port and name the

sensor. The specific alarm then can be reported.

●

If the sensor is prefabricated, only check its settings.

●

The actual value prevails. Only the method of the parameter settings is

described.

Procedure

Step 1 Set water sensor parameters.

NO TE

The default alarm severity of the AI/DI port is Minor. If you want to change the alarm

severity, see How Should I Configure Alarm Parameters.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Choose System Settings > Signal Name Modify. The Batch Signal

Configuration tab page is displayed.

3. Set Device type to ECC800, set Device name to ECC800, and click OK.
4. On the query result tab page, set the new signal name of AI/DI_2 to Leak

and click Submit.

5. Choose Monitoring > System > ECC800 > Running Parameters > AI/DI_2

Port Settings.

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

174

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands