Huawei FusionModule500 User Manual Download Page 264

Page: 264 / 302

Maintenance

Area

Maintenance

Item

Operation

Expected Result Troubleshootin

ECC800-Pro

AC input

Input voltage:

200–240 V AC
Frequency: 45–

55 Hz

If the input

voltage is

abnormal, check

the power grid

status and input

cable

connection.

Output voltage

Output voltage:

53.5 V DC±5%

If the output

voltage is

abnormal, check

the load power

and cable

connection.

Indicator

The indicator on

the power

module is steady

green.

Check the

output voltage

and determine

whether the

power module

is faulty. If the

power module

is faulty, replace

it.

Fan

No abnormal

noise is

generated.

If abnormal

noise is

generated, clean

the fan.

Operating

environment

● Ambient

temperature:

–20°C to

+65°C

● Humidity:

0%–95% RH

(non-

condensing)

If the

temperature or

humidity is

abnormal, check

the smart

cooling product

status.

Monitoring

module indicator

The monitoring

module indicator

is steady green

or blinking

green.

If the indicator

is off or any

abnormal

condition

occurs, see

to rectify the

fault.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

254

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Huawei FusionModule500, User Manual, Page: 264 / 302

Search results

Summary of Contents for FusionModule500

Reviews: