manualshive.com logo in svg

Huawei FusionModule500, User Manual, Page: 41 / 302

Share
Download
Huawei FusionModule500 User Manual Download Page 41

Figure 3-7 ECC800-Pro (rear view)

(1) 53.5V DC_OUT1

(2) 53.5V DC_OUT2

(3) AC_INPUT1

(4) AC_INPUT2

Power Port

The ECC800-Pro provides four power ports, including two AC input ports

(AC_INPUT1 and AC_INPUT2) and two DC output ports (DC_OUTPUT1 and

DC_OUTPUT2). 

Table 3-11

 provides the power port pin definitions.

Table 3-11 Power port pin definitions

Port Type

Pin

sequence

Description

AC

Pin1

L

Pin2

PE

Pin3

N

DC

Pin1

48V+

Pin2

48VGND

 

3.4.3.1.2 Main Control Module

Figure 3-8 ECC800-Pro collector main control module

(1) USB

(2) Status indicator

(3) AIDI_1

(4) AIDI_2

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Copyright © Huawei Technologies Co., Ltd.

31

Summary of Contents for FusionModule500















































































































































































































































































































Reviews:

No comments