Huawei FusionModule500 User Manual Download Page 283

Page: 283 / 302

Figure 6-7 Removing the ECC800-Pro main control module

Step 5 (Optional) Remove the Micro SD card and SIM card from the corresponding slots

of the ECC800-Pro main control module.

Step 6 (Optional) Install the removed Micro SD and SIM card in the corresponding slots

of the new ECC800-Pro main control module.

Figure 6-8 Installing the Micro SD and SIM card

Step 7 Install the spare ECC800-Pro main control module in the ECC800-Pro subrack and

tighten the screws on both sides of the ECC800-Pro main control module.

Step 8 Connect the communications cables and antennas to the ECC800-Pro main control

module.

Step 9 Choose Maintenance > Configuration File and import the backup configuration

file, or set parameters for the devices that connect to the ECC800-Pro to ensure

normal communication.

----End

6.4.3.2 Replacing an ECC800-Pro PSU

Prerequisites

D ANGER

Do not touch the terminals in the rear of a removed PSU to avoid electric shocks.

●

Tool: insulation gloves

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

273

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands