Huawei FusionModule500 User Manual Download Page 294

Page: 294 / 302

Step 2 Remove the cables from the T/H sensor.

NO TICE

After removing cables, wrap exposed terminals with insulation tape and do not

block cable labels. If cable labels are blocked, cables may be connected incorrectly

later.

Step 3 Remove the faulty T/H sensor.
Step 4 Attach the new T/H sensor to an appropriate position on the cabinet door frame

based on the site requirements.

Step 5 Reinstall the cable removed from the T/H sensor.

NO TE

Before removing a T/H sensor, remember the DIP switch setting on it. When you install a

new T/H sensor, you need to set the same DIP switch setting for the new one.

----End

6.4.3.10 Replacing a Smoke Detector

Prerequisites

●

Recommended tools and materials: Phillips screwdriver, insulation tape, step

ladder (2 m)

●

A smoke detector needs to be replaced.

●

A spare smoke detector of the same model is available and functional.

Context

The smoke detector is installed on the top of the cabinet, as shown by (1) in

Figure 6-25

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

284

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands